The product you have selected contains only - aluminum profile - does not include the accessories located in the Accessories tab.
Additional accessories like covers, end caps, electricity conductive end cap, mounting bracket, fasteners, mounting springs, proximity switch, micro switch, mounting system and others are available under "Accessories".
If you are interested in longer lengths than one meter, write to us we will quote the delivery cost to you. Transport companies expect additional charges for long shipments.
For each country is different maximum length of the profile that we can send. It does not depend on us only by courier.
We also do service cutting aluminum profiles to the indicated size - write or call get comprehensive information.
Profile STEKO is a stair profile is made of high-grade aluminum, which has been subjected to double anodizing, which has a high resistance to corrosion and mechanical damage. Profile has a utility in the LED light sources emitting in the headspace. Lighting can be used LEDs in the side of the so-called. "Side view", where the width of the strip does not exceed 7mm. LEDs is recommended to override a special non-slip rope, which is complete with profile STEKO, but is also available as a completely separate article.
The profile has been designed so that it served as a channel for installation LED strip luminous side. The channel is closed with a transparent silicone cord, which aims to act as a shield. The anti-slip rubber strip should be a diameter such that it was possible to mount a so-called. "interference". If we know that the profile STEKO comes into contact with water or moisture LED strip should be placed on the t-shirts seal. In addition, such a construction can be also prepared for example sealed. Silicone.
The LEDs can be embedded in the channel, so that shone in the direction of the rope of silicone, it will be visible points of light, welcome light will be strong. They can also be mounted in a manner in which they shine down the channel, the lines can achieve the effect of light and the effect is very subdued light.
STEKO profile in front of a channel for the current connection, which is also the conduit for the cable. To carry out the power cord from the LED strip to the channel for the wire, it is necessary drilling hole at the marked spot on the inside of the profile.
Profile STEKO is designed for mounting on the edges of stairs, platforms, and many others. Its main task is to protect the edge of the steps and signaling them light.
Installation profile to the ground is carried out using the appropriate screws with countersunk or bevel - lens. Holes for screws should be performed depending on the needs of the lines, which are marked on the inside of the profile. The recommended distance between the screws should be approximately 120 mm. The outer side of the profile openings should be finished so that the screw heads were well below the upper edge serrations.
To be able to apply a profile on the outside do the luminaire of high tightness, the class resistance against the ingress of dirt, dust and water will be IP 67.
Profile are dedicated accessory - polypropylene caps. Their use is intended to protect the profile against the ingress of dust into it and undesirable elements that could lead to the dirt strip, and deterioration in the quality of light.
We invite you to familiarize yourself with our offer.
STEKO profile is designed for mounting on the edges of stairs, platforms, etc. It is designed to protect the edges of steps and indicate them światłem.Jest smaller version of STEP profile designed for softer conditions eksploatacji.Montaż STEKO to the surface by means of the appropriate screws with countersunk or Tapered lens. Screw holes in the profile STEKO carried out depending on the needs of the lines marked on the left side of the profile. The distance between the screws, we recommend to keep within the top 120 mm.Od profile page openings must be finished so that the phase of the screw heads were well below the upper edge of the ryflowania.W profile is provided for mounting channel LED strip light emitting side. LED strip width is 6mm. LED channel is closed for a clear, silicone cord that acts as a shield. Silicone cord diameter is chosen so that it can be mounted on a "push-fit". Profile In case of contact with water or moisture LED strip should be placed on the t-shirts for LED uszczelniającej.Kanał after installation can also be sealed for example. Suitably chosen silicone. LEDs can be deposited in the channel so that it shone in the direction of the silicone cord, then the visible points of light, but the light is visible as well mocne.Można mount LEDs to shine down the channel, then you can achieve the effect of light lines and the effect of light is stonowany.Profil STEKO in front of the terminal has a channel for forming a current passage for przewodu.Aby carry out the power cord from the LED to the channel strip for cable, you need to drill a hole at the marked spot on the inner side of the profile. STEKO accessories.: - Cord Covers STEKO silicone-left and right-screws
Stair profile is made of high-grade, double-anodized aluminum with the option of LED
glowing in the upper half space. Use for lighting LEDs on the side called. "Side view" with a width of 7 mm tapes that the message of a special non-slip rope. Rope slip occurs in the complete profile STEKO, is also available as a separate article. Installation of the base profile is implemented using the appropriate screws with countersunk or conical lens. Screw holes in the profile STEKO carried out depending on the needs of the lines marked on the inner side of the profile. The recommended distance between the screws should copper about 120 mm. On the outer side of the profile openings must be finished phase so that the screw heads are far below the upper edge serrations. As an accessory to the profile are dedicated polypropylene caps. The use of caps protect from dust profile and undesirable elements that can cause contamination LED strip, thus worsening the lighting parameters. You can perform a luminaire with high tightness, whose class resistance against ingress of solid objects, dust and water will be IP 67.
